OK.

It seems to me that I need somehow to activate the following .conf file:

/usr/lib/python2.7/dist-packages/lava_dispatcher/default-config/lava-dispatcher/device-types/beaglebone-black.conf

On Tue, Feb 20, 2018 at 12:28 PM, Neil Williams
<neil.williams@linaro.org> wrote:
> On 20 February 2018 at 11:20, Zoran S <zoran.stojsavljevic.de@gmail.com>
> wrote:
>>
>> Hello,
>>
>> I am bringing now the target Beaglebone Black, as DUT in Lava.
>>
>> Here is my BBB01.jinja2 device definition:
>>
>> {% extends 'beaglebone-black.jinja2' %}
>> {% set connection_command = '/vagrant/scripts/connectBBB.sh localhost
>> 8020 root ""' %}
>> {% set power_on_command = '/usr/bin/egctl egenie on left left left' %}
>> {% set power_off_command = '/usr/bin/egctl egenie off left left left' %}
>> {% set hard_reset_command = '/usr/bin/egctl egenie on left left left' %}
>>
>> Where the line: "vagrant/scripts/connectBBB.sh localhost 8020 root ""'
>>
>> represents as $@ the following: 127.0.0.1 8020 root and "" (""
>> represents empty password, actually <cr>).
>
>
> What password? To connect to the serial port of the device? That looks
> wrong.
>
> If a password is required to login to the booted system, that must be
> supplied in the test job definition using auto login action support.
>
>>
>>
>> It seems that this part works correctly:
>>
>> end: 2.4.1 reset-device (duration 00:00:00)
>> start: 2.4.2 u-boot-interrupt (timeout 00:03:00)
>> Changing prompt to 'Press SPACE to abort autoboot'
>> u-boot-interrupt: Wait for prompt Press SPACE to abort autoboot
>> (timeout 00:03:00)
>> spawn telnet localhost 8020
>> Trying ::1...
>> Connected to localhost.
>> Escape character is '^]'.
>> ser2net port 8020 device /dev/ttyUSB0 [115200 N81] (Debian GNU/Linux)
>>
>> end: 2.4.2 u-boot-interrupt (duration 00:00:02)
>> start: 2.4.3 bootloader-commands (timeout 00:02:58)
>> Changing prompt to start interaction: U-Boot
>> bootloader-commands: Wait for prompt U-Boot (timeout 00:03:00)
>
>
> Your U-Boot configuration did not issue a prompt, it immediately went into
> booting the board with whatever was last installed.
>
>>
>> switch to partitions #0, OK
>> mmc0 is current device
>> SD/MMC found on device 0
>> ** Unable to read file boot.scr **
>> ** Unable to read file uEnv.txt **
>> switch to partitions #0, OK
>> mmc0 is current device
>> Scanning mmc 0:1...
>> switch to partitions #0, OK
>> mmc0 is current device
>> SD/MMC found on device 0
>> switch to partitions #0, OK
>> mmc0 is current device
>> SD/MMC found on device 0
>> ** Unable to read file boot.scr **
>> ** Unable to read file uEnv.txt **
>> 4161168 bytes read in 293 ms (13.5 MiB/s)
>> 35016 bytes read in 23 ms (1.5 MiB/s)
>> ## Flattened Device Tree blob at 88000000
>>    Booting using the fdt blob at 0x88000000
>>    Loading Device Tree to 8fff4000, end 8ffff8c7 ... OK
>> Starting kernel ...
>> [    0.000000] Booting Linux on physical CPU 0x0
>> [    0.000000] Linux version 4.13.8-jumpnow (oe-user@oe-host) (gcc
>> version 7.2.0 (GCC)) #1 Fri Jan 12 13:27:03 CET 2018
>> [    0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7),
>> cr=10c5387d
>> [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
>> instruction cache
>> [    0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black
>> [    0.000000] Memory policy: Data cache writeback
>> [    0.000000] cma: Reserved 16 MiB at 0x9f000000
>> [    0.000000] CPU: All CPU(s) started in SVC mode.
>>
>> But when it comes to login to kernel login, it fails!
>
>
> It cannot login because it's trying to login to the wrong system - whatever
> was last installed, not the one specified in the test job. There are no TFTP
> operations here - that's a problem.
>
>>
>>
>> Starting OpenBSD Secure Shell server: sshd
>> key_load_public: invalid format
>> Could not load host key: /etc/ssh/ssh_host_rsa_key
>> key_load_public: invalid format
>> Could not load host key: /etc/ssh/ssh_host_dsa_key
>> key_load_public: invalid format
>> Could not load host key: /etc/ssh/ssh_host_ecdsa_key
>> key_load_public: invalid format
>> Could not load host key: /etc/ssh/ssh_host_ed25519_key
>> sshd: no hostkeys available -- exiting.
>> Starting rpcbind daemon...done.
>> starting statd: done
>> exportfs: can't open /etc/exports for reading
>> modprobe: can't change directory to '/lib/modules': No such file or
>> directory
>> NFS daemon support not enabled in kernel
>> Starting syslogd/klogd: done
>> Poky (Yocto Project Reference Distro) 2.3.2 beaglebone /dev/ttyO0
>> beaglebone login: [  170.488770] random: crng init done
>> bootloader-commands timed out after 178 seconds
>> end: 2.4.3 bootloader-commands (duration 00:02:58)
>> uboot-retry failed: 1 of 1 attempts. 'bootloader-commands timed out
>> after 178 seconds'
>> bootloader-commands timed out after 178 seconds
>> end: 2.4 uboot-retry (duration 00:03:00)
>> uboot-action failed: 1 of 1 attempts. 'bootloader-commands timed out
>> after 178 seconds'
>> bootloader-commands timed out after 178 seconds
>> end: 2 uboot-action (duration 00:03:00)
>> Cleaning after the job
>> Cleaning up download directory:
>> /var/lib/lava/dispatcher/tmp/84/tftp-deploy-a0ZzPD/ramdisk
>> Cleaning up download directory:
>> /var/lib/lava/dispatcher/tmp/84/tftp-deploy-a0ZzPD/kernel
>> Cleaning up download directory:
>> /var/lib/lava/dispatcher/tmp/84/tftp-deploy-a0ZzPD/dtb
>> Cleaning up download directory:
>> /var/lib/lava/dispatcher/tmp/84/tftp-deploy-a0ZzPD/modules
>> start: 4.1 power-off (timeout 00:00:05)
>> nice /usr/bin/egctl egenie off left left left
>> command output socket 1 - off
>> socket 2 - off
>> socket 3 - off
>> socket 4 - off
>>
>> It seems that empty character as "" in jinja2 is noit well represented
>> (or maybe I need to have somehow <CR>)?!
>>
>> Any advise too this problem?
>>
>> Thank you,
>> Zoran
>> zo
>> _______________________________________________
>> Lava-users mailing list
>> Lava-users@lists.linaro.org
>> https://lists.linaro.org/mailman/listinfo/lava-users
>
>
>
>
> --
>
> Neil Williams
> =============
> neil.williams@linaro.org
> http://www.linux.codehelp.co.uk/