Hi Milosz,
Thanks for the reply.
I will try to get the eth008 if possible , otherwise i will try to make use of TFTP or u-boot methods to run the test job on STM32mp157c-dk2.
Thanks & Regards, Dhanunjaya. P
On Mon, Nov 11, 2019 at 4:57 PM Milosz Wasilewski < milosz.wasilewski@linaro.org> wrote:
On Mon, 11 Nov 2019 at 11:07, dhanu msys dhanuskd.palnati@gmail.com wrote:
Hi Milosz,
Really Thanks for sharing the Information.
I have basic question, we can't able to run any test job for the STM32
without external hardware(PDU) ?
Can you please share the device configuration , which helps to run the
test jobs without "ethernet controlled relay" for the STM32.
https://git.linaro.org/lava/lava-lab.git/tree/shared/lab-scripts/eth008_cont...
As I requested earlier , is there any possibility to run the STM32
specific jobs with any other deployment methods(tmpfs , tftp..etc).
Our boards use EFI for booting and I never tried tftp with that. You might need grub EFI application for that. Alternatively you might use u-boot. I didn't try that either.
milosz
Thanks & Regards, Dhanunjaya. P
On Mon, Nov 11, 2019 at 4:19 PM Milosz Wasilewski <
milosz.wasilewski@linaro.org> wrote:
Well, LAVA will try to switch the device into DFU mode for deployment step. These lines in the device dict do it: '/usr/local/lab-scripts/eth008_control -a 172.27.19.27 -r 1 -s on', '/usr/local/lab-scripts/eth008_control -a 172.27.19.27 -r 2 -s on', Then it will power on the board: '/usr/local/lab-scripts/snmp_pdu_control --hostname lngpdu01 --command on --port 3 --delay 20', After that it will try to flash it using the STM32_Programmer_CLI: '/usr/local/bin/STM32_Programmer_CLI -c port=usb1 -w {LAYOUT} -q', Lastly it will power the board down and flip the dip switches back: '/usr/local/lab-scripts/snmp_pdu_control --hostname lngpdu01 --command off --port 3', '/usr/local/lab-scripts/eth008_control -a 172.27.19.27 -r 1 -s off', '/usr/local/lab-scripts/eth008_control -a 172.27.19.27 -r 2 -s off',
So if you don't have HW moded board, this device dict won't work for you. Sources for the scripts are here: https://git.linaro.org/lava/lava-lab.git/tree/shared/lab-scripts We're using pretty expensive HW in the LAB:
- managed APC PDUs:
https://www.apc.com/shop/uk/en/products/Rack-PDU-Switched-1U-16A-208-230V-8-...
(I couldn't find the exact models we have, they're discontinued)
- ETH008 relay board:
https://www.robot-electronics.co.uk/htm/eth008tech.htm
milosz
On Mon, 11 Nov 2019 at 10:42, dhanu msys dhanuskd.palnati@gmail.com
wrote:
Hi Milosz,
No. Through Manual Setup , we are able to switch between the modes.
Here I have attached the kernel & dtb image for your reference. PFA.
Dhanunjaya. P
On Mon, Nov 11, 2019 at 3:40 PM Milosz Wasilewski <
milosz.wasilewski@linaro.org> wrote:
I think I forgot to ask key question when it comes to this device:
did
you do the HW mod to be able to switch between DFU and OS boot modes without manual step?
milosz
On Mon, 11 Nov 2019 at 10:01, dhanu msys dhanuskd.palnati@gmail.com
wrote:
Hi Milosz,
Thanks for reply.
I am new to the LAVA usage.
I have taken reference from the below link.
https://staging.validation.linaro.org/scheduler/device/staging-stm32mp157-01...
Here I have attached the device_dictionary & device configurations
files, PFA.
Note : I am not able to see the "lab-scripts" to have power
controlled commands in my local repository , is there any specific package need to install in my localhost , can you please share the lab-scripts to have pdu control and also please share the pdu device details if required to connect with the hardware.
Can you please share some references , which i can run some jobs
through any other deploy methods like "tmpfs , tftp " for "STM32MP157C-DK2".
Thanks & Regards, Dhanunjaya. P
On Mon, Nov 11, 2019 at 2:59 PM Milosz Wasilewski <
milosz.wasilewski@linaro.org> wrote:
> > Could you share your device dictionary? You might be missing > flasher_deploy_commands. > > Please check here for reference: >
https://ledge.validation.linaro.org/scheduler/device/lng-stm32mp157-01/devic...
> > milosz > > On Thu, 7 Nov 2019 at 07:48, dhanu msys <
dhanuskd.palnati@gmail.com> wrote:
> > > > Hi Team, > > > > I am trying to run the test_jobs on the specific device type
"stm32mp1157c-dk2" , but its throwing an error message to deploy "flasher" method in the deployment parameters.
> > > > Here I have attached the screenshots for reference. PFA. > > > > Thanks & Regards, > > Dhanunjaya. P > > _______________________________________________ > > Lava-users mailing list > > Lava-users@lists.lavasoftware.org > > https://lists.lavasoftware.org/mailman/listinfo/lava-users