What kind of command do you run to flash over usb?
Le jeu. 28 nov. 2019 à 13:26, dhanu msys dhanuskd.palnati@gmail.com a écrit :
Hi Remi,
We were flashing through USB otg cable.
USB deploy method supported by lava right?
Regards, Dhanunjaya
On Thu, Nov 28, 2019, 17:52 Remi Duraffort remi.duraffort@linaro.org wrote:
Hello,
you should give more information if you want to have a proper answer.
How do you flash the board? is it fully automatic? Is this method already supported by LAVA?
Rgds
Le jeu. 28 nov. 2019 à 07:48, dhanu msys dhanuskd.palnati@gmail.com a écrit :
Hi Team,
How can i deploy RTOS based Application Image on target.
Notes : Target HW : STM32F429I-DISC1. RTOS : Open source RTOS Application Image (RTOS + Application specific code).
We are able to flash the Developed Application Firmware (.out/.bin) through IAR IDE via USB, so we are in plan to make use of LAVA and run test applications automatically.
So , Can you please provide some references to deploy this test scenarios in LAVA.
Thanks & Regards, Dhanunjaya. P _______________________________________________ Lava-users mailing list Lava-users@lists.lavasoftware.org https://lists.lavasoftware.org/mailman/listinfo/lava-users
-- Rémi Duraffort LAVA Architect Linaro
Hi Remi,
As i conveyed to you in earlier mail , we are able to boot the STM32F42xxx/F43xxx by flashing the .hex image file into the target through ST Link utility via USB.
Here I have attached the sequences of flashing the image on board & Board setup. PFA.
Thanks & Regards, Dhanunjaya
Dhanunjaya. P
On Thu, Nov 28, 2019 at 7:17 PM Remi Duraffort remi.duraffort@linaro.org wrote:
What kind of command do you run to flash over usb?
Le jeu. 28 nov. 2019 à 13:26, dhanu msys dhanuskd.palnati@gmail.com a écrit :
Hi Remi,
We were flashing through USB otg cable.
USB deploy method supported by lava right?
Regards, Dhanunjaya
On Thu, Nov 28, 2019, 17:52 Remi Duraffort remi.duraffort@linaro.org wrote:
Hello,
you should give more information if you want to have a proper answer.
How do you flash the board? is it fully automatic? Is this method already supported by LAVA?
Rgds
Le jeu. 28 nov. 2019 à 07:48, dhanu msys dhanuskd.palnati@gmail.com a écrit :
Hi Team,
How can i deploy RTOS based Application Image on target.
Notes : Target HW : STM32F429I-DISC1. RTOS : Open source RTOS Application Image (RTOS + Application specific code).
We are able to flash the Developed Application Firmware (.out/.bin) through IAR IDE via USB, so we are in plan to make use of LAVA and run test applications automatically.
So , Can you please provide some references to deploy this test scenarios in LAVA.
Thanks & Regards, Dhanunjaya. P _______________________________________________ Lava-users mailing list Lava-users@lists.lavasoftware.org https://lists.lavasoftware.org/mailman/listinfo/lava-users
-- Rémi Duraffort LAVA Architect Linaro
-- Rémi Duraffort LAVA Architect Linaro
On Fri, 29 Nov 2019 at 10:44, dhanu msys dhanuskd.palnati@gmail.com wrote:
Hi Remi,
As i conveyed to you in earlier mail , we are able to boot the STM32F42xxx/F43xxx by flashing the .hex image file into the target through ST Link utility via USB.
This is a Windows tool. Is there one available for Linux?
milosz
Here I have attached the sequences of flashing the image on board & Board setup. PFA.
Thanks & Regards, Dhanunjaya
Dhanunjaya. P
On Thu, Nov 28, 2019 at 7:17 PM Remi Duraffort remi.duraffort@linaro.org wrote:
What kind of command do you run to flash over usb?
Le jeu. 28 nov. 2019 à 13:26, dhanu msys dhanuskd.palnati@gmail.com a écrit :
Hi Remi,
We were flashing through USB otg cable.
USB deploy method supported by lava right?
Regards, Dhanunjaya
On Thu, Nov 28, 2019, 17:52 Remi Duraffort remi.duraffort@linaro.org wrote:
Hello,
you should give more information if you want to have a proper answer.
How do you flash the board? is it fully automatic? Is this method already supported by LAVA?
Rgds
Le jeu. 28 nov. 2019 à 07:48, dhanu msys dhanuskd.palnati@gmail.com a écrit :
Hi Team,
How can i deploy RTOS based Application Image on target.
Notes : Target HW : STM32F429I-DISC1. RTOS : Open source RTOS Application Image (RTOS + Application specific code).
We are able to flash the Developed Application Firmware (.out/.bin) through IAR IDE via USB, so we are in plan to make use of LAVA and run test applications automatically.
So , Can you please provide some references to deploy this test scenarios in LAVA.
Thanks & Regards, Dhanunjaya. P _______________________________________________ Lava-users mailing list Lava-users@lists.lavasoftware.org https://lists.lavasoftware.org/mailman/listinfo/lava-users
-- Rémi Duraffort LAVA Architect Linaro
-- Rémi Duraffort LAVA Architect Linaro
Lava-users mailing list Lava-users@lists.lavasoftware.org https://lists.lavasoftware.org/mailman/listinfo/lava-users
Hi Milosz,
Yes. Please reffer the below link. https://startingelectronics.org/tutorials/STM32-microcontrollers/programming...
Dhanunjaya. P
On Fri, Nov 29, 2019 at 4:17 PM Milosz Wasilewski < milosz.wasilewski@linaro.org> wrote:
On Fri, 29 Nov 2019 at 10:44, dhanu msys dhanuskd.palnati@gmail.com wrote:
Hi Remi,
As i conveyed to you in earlier mail , we are able to boot the
STM32F42xxx/F43xxx by flashing the .hex image file into the target through ST Link utility via USB.
This is a Windows tool. Is there one available for Linux?
milosz
Here I have attached the sequences of flashing the image on board &
Board setup. PFA.
Thanks & Regards, Dhanunjaya
Dhanunjaya. P
On Thu, Nov 28, 2019 at 7:17 PM Remi Duraffort <
remi.duraffort@linaro.org> wrote:
What kind of command do you run to flash over usb?
Le jeu. 28 nov. 2019 à 13:26, dhanu msys dhanuskd.palnati@gmail.com
a écrit :
Hi Remi,
We were flashing through USB otg cable.
USB deploy method supported by lava right?
Regards, Dhanunjaya
On Thu, Nov 28, 2019, 17:52 Remi Duraffort remi.duraffort@linaro.org
wrote:
Hello,
you should give more information if you want to have a proper answer.
How do you flash the board? is it fully automatic? Is this method already supported by LAVA?
Rgds
Le jeu. 28 nov. 2019 à 07:48, dhanu msys dhanuskd.palnati@gmail.com
a écrit :
Hi Team,
How can i deploy RTOS based Application Image on target.
Notes : Target HW : STM32F429I-DISC1. RTOS : Open source RTOS Application Image (RTOS + Application specific code).
We are able to flash the Developed Application Firmware (.out/.bin)
through IAR IDE via USB, so we are in plan to make use of LAVA and run test applications automatically.
So , Can you please provide some references to deploy this test
scenarios in LAVA.
Thanks & Regards, Dhanunjaya. P _______________________________________________ Lava-users mailing list Lava-users@lists.lavasoftware.org https://lists.lavasoftware.org/mailman/listinfo/lava-users
-- Rémi Duraffort LAVA Architect Linaro
-- Rémi Duraffort LAVA Architect Linaro
Lava-users mailing list Lava-users@lists.lavasoftware.org https://lists.lavasoftware.org/mailman/listinfo/lava-users
On Fri, 29 Nov 2019 at 10:54, dhanu msys dhanuskd.palnati@gmail.com wrote:
Hi Milosz,
Yes. Please reffer the below link. https://startingelectronics.org/tutorials/STM32-microcontrollers/programming...
So you have the answer. You need a new device type with this tool as 'flasher'.
milosz
Dhanunjaya. P
On Fri, Nov 29, 2019 at 4:17 PM Milosz Wasilewski milosz.wasilewski@linaro.org wrote:
On Fri, 29 Nov 2019 at 10:44, dhanu msys dhanuskd.palnati@gmail.com wrote:
Hi Remi,
As i conveyed to you in earlier mail , we are able to boot the STM32F42xxx/F43xxx by flashing the .hex image file into the target through ST Link utility via USB.
This is a Windows tool. Is there one available for Linux?
milosz
Here I have attached the sequences of flashing the image on board & Board setup. PFA.
Thanks & Regards, Dhanunjaya
Dhanunjaya. P
On Thu, Nov 28, 2019 at 7:17 PM Remi Duraffort remi.duraffort@linaro.org wrote:
What kind of command do you run to flash over usb?
Le jeu. 28 nov. 2019 à 13:26, dhanu msys dhanuskd.palnati@gmail.com a écrit :
Hi Remi,
We were flashing through USB otg cable.
USB deploy method supported by lava right?
Regards, Dhanunjaya
On Thu, Nov 28, 2019, 17:52 Remi Duraffort remi.duraffort@linaro.org wrote:
Hello,
you should give more information if you want to have a proper answer.
How do you flash the board? is it fully automatic? Is this method already supported by LAVA?
Rgds
Le jeu. 28 nov. 2019 à 07:48, dhanu msys dhanuskd.palnati@gmail.com a écrit : > > Hi Team, > > How can i deploy RTOS based Application Image on target. > > Notes : > Target HW : STM32F429I-DISC1. > RTOS : Open source RTOS > Application Image (RTOS + Application specific code). > > We are able to flash the Developed Application Firmware (.out/.bin) through IAR IDE via USB, so we are in plan to make use of LAVA and run test applications automatically. > > So , Can you please provide some references to deploy this test scenarios in LAVA. > > Thanks & Regards, > Dhanunjaya. P > _______________________________________________ > Lava-users mailing list > Lava-users@lists.lavasoftware.org > https://lists.lavasoftware.org/mailman/listinfo/lava-users
-- Rémi Duraffort LAVA Architect Linaro
-- Rémi Duraffort LAVA Architect Linaro
Lava-users mailing list Lava-users@lists.lavasoftware.org https://lists.lavasoftware.org/mailman/listinfo/lava-users
Hi Milosz,
As I mentioned above , I have found the linux based commands to flash my image on target using st-flash as below.
"st-flash --format ihex write /home/dhanunjaya/Downloads/demo_guix_medical.hex".
To run this specific testcases , i have added new device type & device with my basic understanding , upto now i can able to flash the image the as per the command which i have mentioned above using st-flash.
Now , i am little bit confused with the device type configurations , can you please help me out on this.
As mentioned earlier to make use of flasher deploy method , suggest me the device type configurations and also i dont need to maintain the connection to the hardware , why because i will be flashing the .hex image , its a combination of RTOS & Application base , so i will not be having any booting prompt.
If its flasher deploy method , how i can download the images(.hex) into the leshan server , If I Downloaded , then how i can update the Flash Command specific to this type of configuration.
Thanks & Regards, Dhanunjaya. P
On Fri, Nov 29, 2019 at 4:26 PM Milosz Wasilewski < milosz.wasilewski@linaro.org> wrote:
On Fri, 29 Nov 2019 at 10:54, dhanu msys dhanuskd.palnati@gmail.com wrote:
Hi Milosz,
Yes. Please reffer the below link.
https://startingelectronics.org/tutorials/STM32-microcontrollers/programming...
So you have the answer. You need a new device type with this tool as 'flasher'.
milosz
Dhanunjaya. P
On Fri, Nov 29, 2019 at 4:17 PM Milosz Wasilewski <
milosz.wasilewski@linaro.org> wrote:
On Fri, 29 Nov 2019 at 10:44, dhanu msys dhanuskd.palnati@gmail.com
wrote:
Hi Remi,
As i conveyed to you in earlier mail , we are able to boot the
STM32F42xxx/F43xxx by flashing the .hex image file into the target through ST Link utility via USB.
This is a Windows tool. Is there one available for Linux?
milosz
Here I have attached the sequences of flashing the image on board &
Board setup. PFA.
Thanks & Regards, Dhanunjaya
Dhanunjaya. P
On Thu, Nov 28, 2019 at 7:17 PM Remi Duraffort <
remi.duraffort@linaro.org> wrote:
What kind of command do you run to flash over usb?
Le jeu. 28 nov. 2019 à 13:26, dhanu msys dhanuskd.palnati@gmail.com
a écrit :
Hi Remi,
We were flashing through USB otg cable.
USB deploy method supported by lava right?
Regards, Dhanunjaya
On Thu, Nov 28, 2019, 17:52 Remi Duraffort <
remi.duraffort@linaro.org> wrote:
> > Hello, > > you should give more information if you want to have a proper
answer.
> > How do you flash the board? is it fully automatic? > Is this method already supported by LAVA? > > > Rgds > > Le jeu. 28 nov. 2019 à 07:48, dhanu msys <
dhanuskd.palnati@gmail.com> a écrit :
>> >> Hi Team, >> >> How can i deploy RTOS based Application Image on target. >> >> Notes : >> Target HW : STM32F429I-DISC1. >> RTOS : Open source RTOS >> Application Image (RTOS + Application specific code). >> >> We are able to flash the Developed Application Firmware
(.out/.bin) through IAR IDE via USB, so we are in plan to make use of LAVA and run test applications automatically.
>> >> So , Can you please provide some references to deploy this test
scenarios in LAVA.
>> >> Thanks & Regards, >> Dhanunjaya. P >> _______________________________________________ >> Lava-users mailing list >> Lava-users@lists.lavasoftware.org >> https://lists.lavasoftware.org/mailman/listinfo/lava-users > > > > -- > Rémi Duraffort > LAVA Architect > Linaro
-- Rémi Duraffort LAVA Architect Linaro
Lava-users mailing list Lava-users@lists.lavasoftware.org https://lists.lavasoftware.org/mailman/listinfo/lava-users
Hi Milosz,
I was able to make the job successfully complete state without running any tests in the tests in the test job definiton.
But still i need to have support for "refine the Device type as much as possible" to make use of "flasher" method to make use of flasher_deploy_commands in the Device configuration.
Here I have shared the test job configuration file along with test results and device type configuration & device configurations. PFA.
Thanks & Regards, Dhanunjaya. P
On Wed, Dec 4, 2019 at 4:44 PM dhanu msys dhanuskd.palnati@gmail.com wrote:
Hi Milosz,
As I mentioned above , I have found the linux based commands to flash my image on target using st-flash as below.
"st-flash --format ihex write /home/dhanunjaya/Downloads/demo_guix_medical.hex".
To run this specific testcases , i have added new device type & device with my basic understanding , upto now i can able to flash the image the as per the command which i have mentioned above using st-flash.
Now , i am little bit confused with the device type configurations , can you please help me out on this.
As mentioned earlier to make use of flasher deploy method , suggest me the device type configurations and also i dont need to maintain the connection to the hardware , why because i will be flashing the .hex image , its a combination of RTOS & Application base , so i will not be having any booting prompt.
If its flasher deploy method , how i can download the images(.hex) into the leshan server , If I Downloaded , then how i can update the Flash Command specific to this type of configuration.
Thanks & Regards, Dhanunjaya. P
On Fri, Nov 29, 2019 at 4:26 PM Milosz Wasilewski < milosz.wasilewski@linaro.org> wrote:
On Fri, 29 Nov 2019 at 10:54, dhanu msys dhanuskd.palnati@gmail.com wrote:
Hi Milosz,
Yes. Please reffer the below link.
https://startingelectronics.org/tutorials/STM32-microcontrollers/programming...
So you have the answer. You need a new device type with this tool as 'flasher'.
milosz
Dhanunjaya. P
On Fri, Nov 29, 2019 at 4:17 PM Milosz Wasilewski <
milosz.wasilewski@linaro.org> wrote:
On Fri, 29 Nov 2019 at 10:44, dhanu msys dhanuskd.palnati@gmail.com
wrote:
Hi Remi,
As i conveyed to you in earlier mail , we are able to boot the
STM32F42xxx/F43xxx by flashing the .hex image file into the target through ST Link utility via USB.
This is a Windows tool. Is there one available for Linux?
milosz
Here I have attached the sequences of flashing the image on board &
Board setup. PFA.
Thanks & Regards, Dhanunjaya
Dhanunjaya. P
On Thu, Nov 28, 2019 at 7:17 PM Remi Duraffort <
remi.duraffort@linaro.org> wrote:
What kind of command do you run to flash over usb?
Le jeu. 28 nov. 2019 à 13:26, dhanu msys <
dhanuskd.palnati@gmail.com> a écrit :
> > Hi Remi, > > We were flashing through USB otg cable. > > USB deploy method supported by lava right? > > Regards, > Dhanunjaya > > On Thu, Nov 28, 2019, 17:52 Remi Duraffort <
remi.duraffort@linaro.org> wrote:
>> >> Hello, >> >> you should give more information if you want to have a proper
answer.
>> >> How do you flash the board? is it fully automatic? >> Is this method already supported by LAVA? >> >> >> Rgds >> >> Le jeu. 28 nov. 2019 à 07:48, dhanu msys <
dhanuskd.palnati@gmail.com> a écrit :
>>> >>> Hi Team, >>> >>> How can i deploy RTOS based Application Image on target. >>> >>> Notes : >>> Target HW : STM32F429I-DISC1. >>> RTOS : Open source RTOS >>> Application Image (RTOS + Application specific code). >>> >>> We are able to flash the Developed Application Firmware
(.out/.bin) through IAR IDE via USB, so we are in plan to make use of LAVA and run test applications automatically.
>>> >>> So , Can you please provide some references to deploy this test
scenarios in LAVA.
>>> >>> Thanks & Regards, >>> Dhanunjaya. P >>> _______________________________________________ >>> Lava-users mailing list >>> Lava-users@lists.lavasoftware.org >>> https://lists.lavasoftware.org/mailman/listinfo/lava-users >> >> >> >> -- >> Rémi Duraffort >> LAVA Architect >> Linaro
-- Rémi Duraffort LAVA Architect Linaro
Lava-users mailing list Lava-users@lists.lavasoftware.org https://lists.lavasoftware.org/mailman/listinfo/lava-users
lava-users@lists.lavasoftware.org
-
dhanu msys -
Milosz Wasilewski -
Remi Duraffort